My 1987 Porsche 928 S4, 5 speed
|
General Information |
| |
HT Armaflex Brings Closed-Cell Performance to High Temperature applications | |
If high temperature ranges put most flexible elastomeric off limits for your application, consider HT Armaflex. | |
| |
Description | |
| |
HT/Armaflex is a black flexible elastomeric thermal insulation,
supplied as unslit tubing in nominal wall thicknesses of 3/8" (10mm), 1/2"
(13mm), and 3/4" (19mm). It is specially developed by Armacell to perform
in continuous high temperature applications up to +300°F
(+150oC), with intermittent exposure to
+350oF (+175°C). The formulation of HT/Armaflex
provides exceptional ozone and ultraviolet resistance. A closed-cell material, HT/Armaflex provides low thermal conductivity, good fire behavior, low temperature flexibility, and excellent protection against heat flow and water vapor diffusion. It is manufactured without the use of CFC’s, HFC's or HCFC's. It is also formaldehyde free, low VOCs, fiber free, dust free and resists mold and mildew. When installed in the same manner as standard AP/Armaflex flexible insulation, HT/Armaflex requires no additional vapor retarder under normal conditions. Complies with: | |
| |
Resistance to Water Vapor Flow | |
| |
The
closed cell structure of HT/Armaflex prevents moisture from wicking and
makes it an efficient insulation. For most applications, HT/Armaflex
requires no supplemental vapor retarder. An additional vapor retarder may
be necessary when installed on very cold lines or where exposed to
continuous high humidity (see Armaflex Installation
Manual). | |
Uses | |
| |
HT/Armaflex is used as insulation and protection for piping in
solar collectors, refrigeration and automotive applications. The
insulation withstands incidental oil contact and performs on a broad range
of metal pipes and tubing in applications such as:
| |
Installation | |
| |
Supplied in tube and roll form, HT/Armaflex is easy to snap on
or sleeve over pipework for new or existing piping applications. In roll
form, HT/Armaflex installs quickly on large flat or curved surfaces using
Armaflex 625 Adhesive. For pipes and fitting covers, only seams and joints
require adhesive. HT/Armaflex is installed in the same manner as
AP/Armaflex (see Armaflex Installation
Manual). HT625 Adhesive
is required to seal seams and joints. | |
Features -- Benefits | |
| |
HT/Armaflex is engineered to meet more demanding insulation
requirements.
| |
Sundries | |
| |
HT 625 Adhesive -- a powerful contact adhesive that creates a vapor tight seal on systems operating up to 350oF (175oC).
|
HT/ARMAFLEX -
|
Physical Properties |
| |
|
Thermal conductivity,
BTU-in./hr sq ft2 . oF (W/mK)
32oF mean temperature (0oC)
75oF mean temperature (24oC)
120oF mean temperature (50oC)
0.275 (0.039)
0.30 (0.043)
0.32 (0.047)
ASTM C 177 or
ASTM C 518
Water vapor permeability
Perm-inch [Kg/(s m Pa)]0.05 [7.25 x 10-14] ASTM E 96
Procedure A
Mold growth
Fungi resistance
Bacterial resistanceUL 181
ASTM G 21/C 1338
ASTM G 22Meets requirements
Meets requirements
Meets requirements
Water Absorption, % by volume 0.2 ASTM C 209
Upper Use Limit oF(oC) 300oF (150oC) Note: Suitable for systems with occasional or intermittent temperatures to 350°F (175°C), with a recommended exposure limit of one 30-minute period at 350°F (175°C) over 24 hours of operation.
Lower Use Limit oF(oC) -58oF (-50oC) Note: At -20oF (-29oC) flexible HT/Armaflex insulation becomes hard and as temperatures drop below -20oF (-29oC), will be increasingly brittle; however this hardening characteristic does not affect thermal efficiency or water vapor permeability.
Ozone Resistance Excellent ASTM D 1149
Density, typical range, lbs/ft3 3.0 - 6.0 ASTM D 1622 or ASTM D 1667
HT/ARMAFLEX - |
Pipe
Sizes |
Wall Thicknesses | ||
Metric Size
(mm) |
Copper Size
(") |
Iron Pipe Size
(") | |
12 |
1/2 |
-- |
10mm (3/8") 13mm (1/2") 19mm (3/4") |
14/15 |
5/8 |
1/4 | |
18 |
3/4 |
3/8 | |
22 |
7/8 |
1/2 | |
25 |
1 |
-- | |
28 |
1-1/8 |
3/4 | |
35 |
1-3/8 |
1 | |
42 |
1-5/8 |
1-1/4 | |
48 |
-- |
1-1/2 | |
54 |
2-1/8 |
-- | |
57 |
-- |
-- | |
60 |
-- |
2 | |
76 |
-- |
2-1/2 |
Width (all) |
1.00m
(3.28') | ||
Thickness x Length |
13mm x 8m (1/2" x 26.25') |
19mm x 6m (3/4" x 19.69') |
25mm x 4m (1" x 13.13') |